Thin Fans Accessories and Options

FILTERS: All Kooltronic filters consist of a multi-layer grid of sturdy corrugated aluminum, securely held in a one piece aluminum frame. Filters are required whenever air is drawn into an electronics enclosure. A non-drying adhesive coating traps a high percentage of particulate matter. These filters are reuseable, they may be washed and recoated with the appropriate filter recoating adhesive. Replacements are available for those which become damaged or otherwise non-serviceable. See chart below for dimensions.

FILTER HOLDERS: Separate models are available for easy internal or external filter mounting.

GRILLE: Designed to provide flush-mounted, protective guarding. These painted, expanded metal grids fit neatly over the blade side of the S Series fans without adding depth. Used with mounting sleeves, they can provide an alternative to wire guards.

GUARD: Made of heavy-gauge corrosion-protected wire, these guards comply with OSHA and UL safety standards. Individual guards fully protect both blade and motor sides of all B Series fans, except models KB802B. In order to adequately protect the motor side of these and all S Series fans, a mounting sleeve is needed with the guard to accommodate the fan's greater depth.

MOUNTING SLEEVE: Extends the fan's mounting flange, as needed for some installations, such as mounting the B Series fan on the outside of the cabinet. May also be used with guard attachment (see Guard), or with a grille to provide guarding. Made of sturdy formed and welded steel and painted to match the fan.

Typical Accessory Combinations and Mounting Orientations

Arrows show direction of airflow. Boxes represent electronics/electrical enclosures, side view.

Mounting Orientations

Upper fans exhaust cabinet. Lower fans pressurize cabinet. (Note that intake air is filtered.)

**B and S Series Fans when mounted in intake orientation may require an additional Mounting Sleeve. Check dimensions or contact Kooltronic. Mouting Sleeve Chart

Model Number and Dimensions for Thin Fan Accessories


ACCESSORY	FAN MODEL (B OR S)
	KB650/651	KB800/802	KB900	KB1000
Filter Size (0.50"[12.7mm] thick)	650F 8.38 x 8.38 [212.9mm x 212.9mm]	800F 10.38 x 10.38 [263.7mm x 263.7mm]	900F 11.38 x 11.38 [289.1mm x 289.1mm]	1000F 12.38 x 12.38 [314.5mm x 314.5mm]
External Filter Holder Click model for dimensions	650H	800H	900H	1000H
Internal Filter Holder Click model for dimensions	650HF	800HF	900HF	1000HF
Grille Diameter	650X 8.50 [215.9mm]	800X 10.5 [266.7mm]	900X 11.50 [292.1mm]	1000X 12.50 [317.5mm]
Guard Diameter X Depth	655G 8.43 x 2.69 [214.1mm x 68.4mm]	805G 10.66 x 2.69 [270.8mm x 68.4mm]	905G 11.78 x 2.69 [299.2mm x 68.4mm]	1005G 12.90 x 2.69 [327.7mm x 68.4mm]
Mounting Sleeve Click model for dimensions	650M	800M	900M	1000M
All B Series fans using the filter holder, filter and grille combination must use mounting sleeve.
Dimensions, inches [mm], are for reference only and subject to change.

AUTOMATIC SPEED CONTROL: The Kooltronic Fan and Blower Automatic Speed Control (Part Number KSC100) is a solid state "smart" controller packaged in a NEMA 1 type enclosure for remote mounting. The allowable input power supply range is 95 to 250 Volts, 47 to 63 Hz. It is furnished standard with an IEC 320 connector, a power supply fuse and a temperature sensor. Additional temperature sensors are optional. Power Cord is not provided.

The controller will operate single or multiple fans or blowers of compatible voltage and frequency up to a combined load of 6 Amps. The controller may be operated by either a control voltage signal of 0 to 10 VDC, a control current signal of 0 to 20 mA or one to three temperature sensors. With multiple temperature sensors the controller will respond to the highest sensed temperature.

The control circuit board is furnished with a terminal strip for field connecting the sensor and fan wires. A pressure type strain relief connector is furnished in the enclosure. If required by the installation or by code, this connector can be replaced with a 1/2-inch [12.7mm] trade size conduit connector.

A wide variety of control logic options can be field programmed into the controller by means of a board mounted DIP switch. These include fan idle or starting speed at 30%, 40%, 50% or 60% of supply voltage, fan on or off below the idle setting, control temperature setting of 86°F (30°C), 95°F (35°C), 104°F (40°C), 113°F (45°C), and temperature differential settings of 7°F (4°C) and 18°F (10°C). The selectable fan on/off feature is operative when the temperature(s) drop below the control temperature setting.

Consult factory for use with compatible Kooltronic fans or blowers.
Click here to view Operator's Manual (pdf)

DRAWINGS AND DIMENSIONS
Click on image for larger view

Speed Controller General Arrangement Drawing

Dimensions, inches [mm], are for reference only and subject to change.

Contact Info:
	Kooltronic, Inc. 30 Pennington-Hopewell Road Pennington, NJ 08534 USA
	609-466-3400 800-321-KOOL
	609-466-1114 (fax)
	Contact Us